国产在线精品一区二区不卡顿|无码专区久久综合久中文字幕|区二区欧美性插b在线视频网站|精品人妻系列无码人妻免费视频

HomeHotlineContact
0position:Home>>News

Analysis of the reasons for the creeping and vibration of the edge milling machine

source:   author: time:2020-08-15 Visits:1653
There are many obvious abnormal phenomena in the milling machine, but in some economic CNC systems, there is no alarm. Even if there is an alarm sometimes, the alarm information shows that it is not the alarm of abnormal phenomenon you see. The creeping and vibration of the milling machine is an obvious example. When the milling machine runs at a low speed, the worktable of the CNC milling machine moves forward in a creeping manner; when the milling machine runs at a high speed, there will be vibration.

Because of the bad lubrication, the friction resistance increases when the milling machine table moves. When the motor is driven, the table does not move forward, which makes the ball screw produce elastic deformation and stores the energy of the motor on the deformation. When the motor continues to drive and the elastic force produced by the stored energy is greater than the static friction force, the milling machine table creeps forward and moves in this way again and again, resulting in crawling phenomenon.

Because the vibration frequency is proportional to the speed of the motor, the first thing to do is to check whether there is a fault in the motor, check the surface condition of the carbon brush and commutator, as well as the mechanical vibration, and check the lubrication of the ball bearing. The whole inspection does not need to be disassembled completely, but can be observed by the inspector. The bearing can listen to the sound with ears To check. If there is no problem, check the tachogenerator. The tachogenerator is usually DC.

A closed loop system may also cause system oscillation due to poor parameter setting. However, the best way to eliminate this oscillation is to reduce its magnification, to adjust RV1 and reverse clock direction in the FANUC system. At this time it can be seen that it will become better immediately. However, because of the relatively small range of RV1 regulating potentiometers, sometimes it can not be adjusted, it can only change the short circuited bar. Cut off the feedback resistance and reduce the magnification of the whole regulator.

More edge milling machines, with pressure beam milling machine, no pressure beam edge milling machine, end face milling machine, end face milling machine, planer. Please pay attention jxsmyy.com


All rights reserved:WUXISHI XILI MILLING MACHINE CO.,LTD(jxsmyy.com)  Su ICP 15043207-1 Design :25318.cn

亚洲av无码乱码在线观看性色| 99精品久久毛片a片| 国产精品成人午夜电影| 亚洲中国精品精华液| 久久国产精品偷| 伊人久久大香线蕉无码不卡| 国产对白老熟女正在播放| 精品中文字幕有码视频| 国产亚洲精品久久久久蜜臀 | aaaaaa级特色特黄的毛片| 成人精品av一区二区三区| 白嫩少妇喷水正在播放| 久久综合久久综合九色| 色欲色香天天天综合无码www | 国产一区二区三区在线视頻| 成在线人免费无码高潮喷水| 青青草原综合久久大伊人精品| 国厂精品114福利电影免费| 成年片色大黄全免费网站久久| 久久久综合香蕉尹人综合网| 色偷偷一区二区无码视频| 欧洲黑大粗无码免费| 精品少妇人妻av无码专区| 成人免费无码av| 人人超碰人摸人爱| 欧美熟妇丰满肥白大屁股免费视频 | 亚洲国色天香卡2卡3卡4| 国产成人a在线观看视频免费| 成人做爰视频www网站| 大地资源网中文第五页| 亚洲高清乱码午夜电影网| 国产精品无码一区二区在线观一 | 10000部拍拍拍免费视频| 成人做爰100部片免费下载| 精品国产sm最大网站| 国产精品va在线播放我和闺蜜| 久久久无码人妻精品一区| 999久久久无码国产精品| 国产成人永久免费视频| 国产真实夫妇交换视频| 加勒比一本heyzo高清视频|